Search
  • Concrete Coatings Nashville

How to Prep Garage Floor for Epoxy

Updated: Sep 5


Fresh garage look after epoxy
Fresh garage look after epoxy

How to Prep Your Garage Floor for A Job, Step by Step


The epoxy floor is an important component of your garage. It provides a hard, durable surface that will resist the abuse of tires and other automotive equipment. The epoxy coating also protects against water damage and can easily be cleaned with soap and water. If you're planning on epoxying your garage floor, then it's important to properly prepare the surface before you begin applying epoxy. The process takes about two hours for one coat; this article will detail each step by step process on how to prep your garage floor for epoxy.


Step One - Cleaning the Floor Surface


To install epoxy on garage floor, you'll first need to clean it. Simply wash away dirt using warm water mixed with liquid dishwashing detergent. As a safety note, epoxies are highly flammable so you should never use a power washer or similar equipment to clean the epoxy floor.


Step Two - Applying a Primer


Before applying epoxy coatings to your garage floor, it's important that you first apply an epoxy primer! This is because epoxies have been known to chemically react with oil-based products and chemicals; as such, priming the surface before coating will ensure that any chemical substances don't interact with the epoxide itself. In addition, this also ensures proper adhesion between two separate layers of epoxy (i.e., if you plan on layering more than one layer). Primers can be purchased from most home improvement stores and epoxy manufacturers. You'll also need a paint-roller or sprayer to apply the primer evenly over the surface of your garage floor.


New clean look after epoxy installation
New clean look after epoxy installation

Step Three - Applying an Epoxy Coating for Garage Floors


Now that you've applied epoxy primer, it's time to move onto adding epoxies! Using a paintbrush (or roller) will ensure even coverage; just make sure not to use too much epoxy at once as this could cause small bubbles in your coating which can be difficult to remove later down the line. In addition, don't forget about any areas where tires roll through such as inner corners and edges; these are prime spots for chemical build up so take extra care when applying epoxide to these areas. Allow epoxy coating to dry completely before continuing onto step four!


Step Four - Brushing on a Topcoat


Once epoxies have dried, apply another layer of epoxy topcoats for garage floors. Again, make sure that the first coat is properly allowed to dry, or you'll run into some problems with adhesion later down the line! Once fully cured (usually between six and eight hours after application), it's safe to move your car back into the garage as well as park your motorcycle without fear of scratching up newly applied epoxide layers. And if you're worried about tire marks showing up against freshly epoxied surfaces then don't be most home improvement sells special products meant specifically for epoxy floors that can be used to clean up epoxies.


Putting on the top coat epoxy
Putting on the top coat epoxy

Step Five - Cleaning Up and Caring for Your Garage Floor


After epoxy floor installation, you'll want to avoid any scratching or damage from tires, motorcycles, etc. which could cause chemical reactions with the epoxide layers. This means avoiding using oil-based soaps when cleaning your garage floor; instead opt for a gentle dishwashing liquid such as Dawn to prevent damaging your epoxied surface! Once fully cured (usually between six and eight hours after application), it's safe to move your car back into the garage as well as park your motorcycle without fear of scratching up newly applied epoxide layers. And if you're worried about tire marks showing up against freshly epoxied surfaces then don't be most home improvement sells special products meant specifically for epoxy floors that can be used to clean up epoxies.



Wax used for epoxy process
Wax

Step Six - Apply a Sealer or Wax


Finally, you'll want to apply another protective layer of sealant (or wax) to keep your garage floor's epoxide coating protected from dirt and chemicals as much as possible! This will help ensure all-day protection against any harmful substances which could compromise your newly applied coating layers!


Final Thoughts.


In the end, epoxy coating your garage floor is a great way to add extra value to your home while sparing no expense for increased safety, improved aesthetics, and creating an all-around enjoyable environment. In addition, epoxying over existing concrete floors helps make it easier to clean up spills or chemical leaks which could otherwise be damaging if not corrosive to bare surfaces. It's important however that you do prep work beforehand in order to ensure proper adhesion between layers as well as protection against tire marks and other chemicals/substances which could pose a risk for damage down the line good luck!




7 views0 comments

Recent Posts

See All